STANDARD FEATURES:

• xx” long by 101.5” OD & 88.5″ wide inside.
  
• Side height 24, 30, 36, 42, 48, 54, 60, Sloped 60-48; 60-54, 66-60 + Board 6” or 12”
  
• Single Wall (Hybrid): Hardox 500 body formed walls w/ 45-degree floor corners w/4×6
  Formed top tube 4mm Standard. Options 3/16; 1/4
  
• Single Wall (Square): Hardox 500 body formed walls w/ 45-degree floor corners w/4×6
  Formed top tube Options 3/16; 1/4
  
• Single Wall (Radius): Hardox 500 body formed walls w/ 45-degree floor corners w/4×6
  Formed top tube Complete 4mm Hardox 500 Box with 3/16 500 Floor (HWK Standard)
  
• Floor Options; Hardox 500, 4mm, 3/16″, ¼” or 3/8”
  
• 8″ high front board pockets set for finished sideboards.
  
• Front, Doghouse, Walls: 4mm or 3/16″ Hardox 500.
  
• 3/16″ 50,000 hoist tower and 3/16” rear posts.
  
• Hat Sills; 9.5″ x 3/16” or Box Length over 18’; ¼” Hat Sill longitudinal rails. (No
  Crossmembers)
  
• 1/2″ X 2 ½” vulcanized rubber buffer strips between box long members & Truck
  frame. – Optional
  
• 10″ x 2” 3/16” Structural Formed tube channel rear cross member.
  
• Cab guard, low profile style. 18” or 24” with Oval Cutout for Strobes
  
• Air Operated valve to limit body dump angle. – Optional
  
• Body prop, integrated to Hoist Saddle (Unloaded body only).
  
•  Body mounted on chassis, locate body 6″-10” behind cab on chassis.

TAILGATE:

• Hardox 500 4mm, 3/16″ or ¼” Formed Tailgate.
• Formed center horizontal rib.
  
• Tailgate air cylinder operated with over center locks and heavy-duty hardware.
  
• 3/8″ tailgate spreader chains with storage hooks. Mesh chain covers on tailgate
  spreader chain plates to protect paint from chains.
  
• Hydraulic or Air high lift tailgate, with ¼” Hi-Tensile steel shielded lift hoods, 2.5″
  x 16″ hydraulic powered lift cylinders with standard tailgate hinges welded at
  ends of lift hoods. Tailgate hinges and tailgate top even with top of lift hoods –
  Optional
  
• (2) or (4) Slurry Locks installed on tailgate – Optional

LIGHTING:

• Recessed legal lights all sealed beam with Philips sealed wire harness system with
  WeatherPac & Bullet ends.
• Oval High Count LED Backup Light Rear Post.
• 2 LED oval stop/tail/tum lights in each rear post of body. (if space permits
• All lights LED

Finish:

• Body Fully sandblasted.
  
• Body Fully primed outside with Endura Polyurethane. 2-3mm Thickness
  
• Body Fully painted outside with Endura Polyurethane. 2-3mm Thickness
  
• Underside of body painted same color as body.
  
• Total mm thickness 4-6mm

CHASSIS EQUIPMENT:

• Masterbrand or Mailhot, Nitrated hydraulic cylinder with 45-50 degree dump angle.
• Optional: Pin to Pin; A Frame or Trunnion mount. Subject to box Length.
• Chelsea / Parker PTO mounted on bottom of transmission.
• Chelsea / Parker gear pump direct mounted to PTO.
• Chelsea / Parker 3-section control valve, first section cable controlled for dump
  body raise/lower, second section cable controlled for pup trailer raise/lower,
  third section air controlled for high lift tailgate raise/lower. – Optional
• Neustar 35G Top frame mounted Tank, Saddle & Dump Prop Combo
• Buyers 25 Steel; 35 or 50 gallon aluminum oil tank; Frame Side or Top Mounted
• Apsco dump body control console, cab mounted between bucket seats. Air
  controlled. Optional Detented.
• Console mounted switches for truck gate, trailer gate, trailer tongue lock, high lift
  tailgate. – Optional
• Hydraulic high lift tailgate controls consisting of: Air controlled valve section
  added to control valve with external relief valve to limit pressure to tailgate.
  Console mounted air toggle for tailgate raise/lower control. Electric over air
  interlock to prevent tailgate from being raised until gate latch hooks are open. – Optional
•  High Mount 22”-24” or Low mount 18-22” trailer hitch with 20T or 50 Ton air
  compensated pintle hook. With all necessary trailer wiring. (7 Wire, & Trailer 7 Wire ISO)
• Pony trailer hydraulic hoses including 1″ wet line to trailer hitch with 1″ quick coupler
  for trailer.- Optional
• Greaseable HD dump body hinges. 2” Solid Shaft Pins Body hinge bushing with grease
  zerc.

• Neustar custom fabricated Tarp housing. Housing width 96″.
  
• Electric arm tarp system with high mounted outboard arms. Asphalt tarp
  material. No side flaps on tarp. Console mounted rocker switch for tarp in/out
  control. side boards provided with tarp installation.
  
• Neustar, shovel holder on driver’s side front panel of body.

• Mud flaps installed in front of first lift axle.
  
• Mud flaps behind drive axles.
  
• 3500 12VDC dump body vibrator install under body where space permits.
  
• ¼ x 6″ rubber spray guards full length of body, both sides.
  
• Two steps and one grab handle on driver’s front comer of dump body, toe step on inside
  front corner of body.